ivoler 4 Pack Screen Protector Compatible with Nintendo Switch OLED Model 7 '' 2021 with Alignment Frame Tool, Tempered Glass Protection Film - without air bubbles -Ultra Resistant Hardness 9H

I paid for this product myself.Having picked up the OLED Switch, the first thing I wanted to do was to protect that lovely screen.This set comes with the guide frame, 4 x glass screen protectors, 4 x sticker sets, 4 x cleaning wipes and a small card to help push out any air bubbles.I was pleased to find the wet wipe was really wet, I often come across these and they’re barely damp. You need to give the screen a really good clean, not just a quick wipe over, even if the like mine. Spend a good minute going up/down, left/right and circular motions. Then dry it with the other cloth. These cloths are not that big and you do need to avoid touching the screen with your fingers, otherwise you’ll need to start again.Having done the cleaning part. Bend the small end of the dust sticker upwards and then use this to remove any specs of dust on the screen. A tiny speck will show up like a 5mm circle under your screen protector. Put the dust removal sticker back on the paper it came on.Pop the guide frame on. When your ready to put the protector on, give the screen one final go with that dust remover sticker. Now, this set does come with guide stickers, which aren’t really needed, since you have the frame. While holding the edges, peel off the backing, and then align the screen protector with one side of the frame and carefully lower it down, using the frame to guide you. Don’t rush it, as it is still possible to misalign it.You’ll then see what looks like liquid run between the Switch screen and screen protector. This should fully covered the screen. It you have any bubbles, use the thick card to push then out to the edge (you cash do this even after you remove the guide frame). Whilst holding the screen protector in place with your fingers, gently remove the frame.If everything is ok, you can use the wet wipe to give the screen protector a clean and then dry it. Personally, I like to leave mine to cureMine went on perfectly first time, but then I am quite experienced at doing these, with or without a guide frame. There’s no reason why yours shouldn’t also. You have some spares should it go wrong.Once on, it’s hard to tell the screen protector is there. It crystal clear and doesn’t have any detrimental affect on the sensitivity.It’s important to remember that the screen protector is there to prevent scratches and such like to the screen. It’s not there to provide drop or impact protection, although it will by the nature of it provide a little.If you’re down to the last screen protector set, just a word of caution. The wet wipes can dry out over time, even when sealed. You might want a standby option should that be the case. You can get screen cleaning sprays, that works for TVs, monitors, phone, laptop, etc. One of those could be fine.A personal tip: I like to have my device sitting on a clean microfibre cloth when doing it and I do the application in a “as dust free” environment as I can.For £9.99, I personally think these are excellent value for money.I hope you found this review & photos interesting, informative, and useful. Thanks for reading.

I've had some stressful screen protector experiences in the past, so I went into this with low expectations and a great big bundle of nerves. However, this was very nicely priced for 4 protectors, well packaged including a nice plastic case for the extras, and a frame that claimed to make alignment easy. I was hesitant enough of the process to insist on getting a 4-pack because I am used to ruining at least 1 as a trial!The cleaning, drying, and dust remover packets were easy to use. Sliding the frame on was easy, yet a sure fit, and the backer from the protector came off without struggle. The frame is amazing, taking all doubt out of the alignment. It also kept me from smudging a fingerprint on my freshly cleaned screen! The bubble remover card was handy and the screen protector applied without a single bubble or any struggle getting even and invisible adhesion.In past experiences, other protectors have had a weird tactile sensation at the edge, but this one was perfectly smoothed in a way that I wouldn't have thought possible. Also, the fit of the corners to the 7" Switch Oled screen are not sharply squared, but not too rounded where any coverage was lost.I absolutely would recommend this product and will be buying again in the future as the need arises, especially if they offer the frames sized for our other tech!

I can't believe how cheap these are! When I saw this price for 4 protectors I wasn't expecting much, but they arrived in a very premium plastic case (good as you will end up with 3 spares that you'll want to store securely!)... I didn't even need the little frame that's included as they're such a perfect match for the size of the screen it's not hard to freehand the position (no guessing how much room to leave around the edge, and it's truly edge to edge!)Once on its nice and smooth, nice and clear, and does a perfect job of showing off the colour and clarity of the display! Well worth a purchase compared to much more expensive alternatives!

I'm glad it comes with spares, as despite getting no bubbles or dust under it on my first attempt, there were two areas with a "rainbow effect", possibly as a result of the excessively wet wipes having left a residue that hadn't completely dried yet (I was sure it was sufficiently dry, but the metal body of the OLED consoles also results in condensation much easier, which may have been a factor).The guide makes lining up a protector fairly simple, but I did find the plastic frame a bit awkward to get squarely over the console, and as I lay down the screen, I had to pull off the guide from around it before it had fully stuck, as the frame was actually preventing the bottom right corner from going all the way down. But once on, they're great, and feel very durable. I don't dare risk putting my console in the dock without a screen protector, even if the insides of the dock look like they use a softer material than the launch models.