40mm Headphone Speaker Driver 32ohm for Bose QC45 QC2 QC15 QC25 QC35 QC3 AE2 OE2, Studio 2 Studio 3, Solo 2 Solo 3, Kraken 7. 1, Akg K55, Marshall Major 2 Headset Replacement Speaker 1pair

Good quality. Sound like original. Easy to install.

Just installed these on my Bose QC25s. I had tried a method shoving bits of paper in the speaker in the past that helped the problem temporarily but eventually the speaker went fully out. Buying a new pair is expensive, and frankly just feels wasteful. I was a little cautious after reading some reviews that sound quality wasn't the same but i havent noticed a difference at all. Installation was pretty straightforward, youll need a soldering iron, hair dryer, small Philips head, and glue (i used super glue) this was my first time using a soldering iron and i didn't have any issues. Sound quality and noise cancellation are the same, and for the price i would say i came out ahead.

Had a speaker go out on my son's Audio Technica ATH-S700BT headphones, it made the headphones sound like the balance was way off to one side and no bass whatsoever from that dead speaker. Searched around for a decent replacement 40mm speaker @ 32ohms, which is what the original speaker tested out to be on the meter. Found these and the overall ratings were good, thought I'd take a chance on them. Item arrived right on time and speaker slipped into the housing ever so slightly loose, which is actually a good thing. Bigger would have been impossible to fit in the housing and most likely distort the frame which would have ruined the sound. A little hot glue around the edge of the frame and speaker, soldered in the wires and put it all back together, the sound is a perfect match with the other original speaker! I had already figured I'd have to change both to get the sound balanced, but its exactly the same characteristics as the oem speaker. Just an fyi, if you plan to replace your speakers in an AT headphone like this model, you'll most likely need a security torx or allen driver to remove the 3 screws inside. You can also try some jewelers flat tip screwdrivers,which is what I ended up doing since none of my bits would fit those screws. It wasn't that hard to remove, but be careful not to slip and poke a hole in the speaker when re-installing it. Overall, I'm very happy with how this turned out! These were not cheap headphones, and having to throw out over a hundred bucks worth of headphones is ludicrous! We'll see how much longer these last now that it has a new speaker in it, at least I have one more I can swap out if it goes again!

I had a Sennheiser HD200 series which is around 6-7 year old now and the left one stopped working a few days ago. Going by the reviews I felt that these would give them life back. They indeed worked like a charm. Fit is marginally loose but that's not actually a bad thing. A little glue on the edges did the trick. They sound really good as compared to the original Sennheiser drivers. My only complaint with them is they have very booming bass and missing the punch. It may be due to the sennheiser housing. I will try to add some damping material and see. Overall they have great quality, realistic mids and crystal clear highs. My next step is to take my headphones to the next level and make them wireless with a fiio BTR3. Great product. You won't regret.

I replaced my Bose QC25 driver after it went out from a decade of happy use. Soldering this driver back into the headset was probably the easiest part of the overall installation, and it immediately worked and I could not tell a difference between it and the original driver still functioning on the other side. 10/10 would recommend replacing your driver instead of dropping $300 on new Bose

I bought these to replace one of my QC25 speakers. After replacing the broken speaker, I noticed the new speaker sounded different from the old one on the other side, so I replaced the other one too. Fortunately, both new speakers work properly (with and without the sound cancellation function turned on). Unfortunately, the new speakers are low quality when it comes to sound/audio fidelity. The sound is now flat and muddled. The bass is too loud. They don't sound anywhere near as good as the original speakers that came with my QC25. In fact, they just don't sound good at all really. That said, the speakers do work, and the price was cheap (about $20), so I'd recommend them for a short term replacement until you can buy a new headset that has good sounding speakers in it. PS: if you plan to buy Bose then know that they release headphones with speakers in them that have a design flaw such that a speaker dying within a year or two is relatively common and possibly even likely. Buy a different brand.

I replaced the stock speakers on my Sena SMH10 communicator with a set of these. I 3D printed a set of grills to protect them in the helmet. These speakers were a massive improvement! They have much better clarity and volume. They sound especially good when wearing earplugs in my helmet whereas earplugs just made the original speakers sound muddy and muted. I have a video on how to do the speaker conversion on You Tube. I can't post a link so search there for "sena speaker upgrade how to" by Shell On Wheels

Don't throw away your headphones, use these speakers to fix them!!! I went on YouTube and learned how to fix them, which was very easy. Didn’t think these inexpensive speakers would do the job, but they sound like new.

Did the job

I tried using only one of these to repair a single broken driver and there was a noticable volume difference between the sides so I had to replace both in the headphones in order to get a sensory match. However, once that was done the sound was very good.

So far so good, Fast delivery and came as shown in the photo. I used these to replace my original speakers in my 3M, Bluetooth Work Connect headset. Also they are substantially louder than the originals. The original speakers have a protective plastic cover on them which can be removed with a flat head screwdriver. There is glue on the black cover which makes it seem to be a 1 piece speaker but it is not. I did not put glue back on it when installing them on the new speakers. I also used a little bit of soapy water to lube the rubber grommet that surrounds the speaker. Thank you!

Perfect headphone speaker replacements

Product is as described and is a direct fit replacement for the Bose QC15 Headphones. I'm fairly handy but my soldering skills aren't great. I figured I would give these a try to resolve an intermittent humming issue in my right earphone, before coughing up hundreds for the latest version of QC's. With the help of a repair video on YouTube, I was able to install these in about 20 minutes. My headphones now sound as good as new! Super happy with this purchase. Great product!