XMT-MOTO Left & Right 1 1/4" 32mm Engine Guard Highway Foot Pegs Footpeg Footrest - Chrome

If you are dumb and have no common sense do not order these, they have no instructions. If you can find solutions to simple problems then you’ll have no issue installing them and should order these. They are great quality and match the stock floor boards and passenger pegs perfectly.

You get what you pay for. These look exactly like OEM, but they are half the weight of Harley’s steel version. The finish feels like paint, as I’m sure they are. They easily scratch, but hey, they’re highway pegs. They feel flimsy and have already stripped out on one side. I had to use my OEM bolt, which is slightly longer, and have a finer thread, but they’re holding. $55? You get what you pay for.Update: Junk! Do not waste your money

These are decent but there are some issues. No instructions but they are pretty self explanatory so Iit wasn't too big aof a deal. they don't provide anything to protect the highway bars so when you attach these you will scratch your highway bar paint. the size was off site a but and the curve of the clamps doesn't fully connect with the bar. It took everything I had to tighten the to the point that they wouldn't rotate when I use them. the set crews to tune the angle of the foot peg move so easy that it leads me to believe they are not threaded correctly, I applied locktite to keep them from moving on there own but it may not be enough.

I like how it was a cheap alternative.Just installed them yesterday, and went on a ride around the block. The amount of customization is awesome as you can customize the position on all 3 axisOn her maiden voyage, I lost 2 of the set screws, and almost a third. The set screws handle the pitch of the foot pad, while not structurally necessary, it's part of a comfort setting.I have now lost all set screws and have no intention of replacing them. Only took about 80 miles to lose them all

At first glance they fit like stock Harley pegs. They look absolutely fabulous. But like some other people have said I have not been able to get them so tight that they won't move with the weight to your foot on it. It is a shame because I really like the look of the peg. I don't know if it's a design flaw or I'm just picky but they do move and I have crank them so hard I've almost stripped out the Allen key.What do some troubleshooting to see what I can figure out.2019 street glide special

2019 Street Glide Special.Out of the box, these pegs did not work. I was ready to fold in the towel at first. They simply would not grip the engine guard tight enough to not slip no matter how hard I cranked on the bolt. I had to sand some of the paint off the inside of the clamp and I used a single wrap of black duct tape on the engine guard bars for grip in order for these to not slip (as many others have experienced). When you do this, you're going to need a clamp on the clamp to squeeze it tight enough to get the bolt started (if that makes any sense). Additionally, getting the shims/flat springs in between the peg and the clamp was a pain in the rear. Basically, assembly and installation is not easy w/o some effort on your part.These are likely a potted metal and NOT steel. They are painted and NOT powder coated. Expect that they are somewhat lightweight and will scratch easily (you will scratch them during assembly of the spring/shim).Having said all of that.... If you're not 400 lbs and standing on them directly, they seem like they'll hold up just fine. but they are 1/4 the price of the branded hardware that they look eerily similar to.... If these break or fail I won't be out too much coin and can then justify paying 4x for ones w/a logo stamped on them.

I like the look and feel. The only dis-satisfaction is they do not clamp tightly on Harley bars. I had to take a small piece of a junk bicycle inner tube to make it fit tight. Other than that they are fine and a fraction of the cost of HD, (which probably explains the poor fit)

There are no directions. not even pictures. It looks easy enough, DOESN'T IT?! After a bit, I had to get a buddy to help and it still took 20 minutes to figure it out. So while I really like them, You're going to need a beer after installation. But they look good.