ECCPP Towing Mirrors Replacement fit for Ford for F250 for F350 for F450 for F550 Power Heated Signal Pair Mirrors 2008 2009 2010 2011 2012 2013 2014 2015 2016

If you understand what you're getting, you won't be disappointed. First off, these only have heated mirrors on top. The bottom convex mirror is not, unlike my factory mirrors. Secondly, as many have stated, the side to side controls are opposite. It's really not a big deal and you get use to it fast. Now, in regards to the ambient air sensor. Access and the wiring is there for the sensor. Simply pull off the old sensor from your old passenger mirror ( its located on the bottom side and can be pryed out)and plug it in. Yes, the connector is different, but it will work. Also, just place the sensor up into the mirror. The access hole is a different size so the original sensor wont fit. Note the plug can be put in either way. It doesn't matter on the sensor. Now you will likely have to reset the sensor. My kept showing -40f. For my 2012 F250 you start the vehicle, put it in drive (with brake on obviously) and power on your climate control. Now hold down the a/c button and the recirculation button (right next to it) for a few secs. Release then push the a/c button once. The sensor should reset work properly. The only negative I have so far is the mirrors to vibrate a little, but to under $200 I am very happy.

Worked great on my 2010 dually and look good.

I went with these as I had a King ranch and the mirrors were shot. I had power fold and telescoping but these did not - but I knew this.Of items on them, the wiring calls for a common ground for up / down mirror control. I have a 2012 F350. This is not the case. Each function uses a different ground, so you have to first cut the parallel ground wire in the mirror and run a new wire or use one of the temp sensor wires (driver side only - need passenger) and then jumper to position 8 (from their diagram) on the down stream fomoco harness which is the second common. You may also need to swap positives and negatives on each. It was a last minute frustration to fix and make the up switch go up etc.Second, if you are handy, the unit is prebuilt for the electronic trailer mirrors. Mine were ok so I used the oems as donors. However: the outrigger supports are narrower on these than the oem by about 1/2 inch. The drive rod needs to be modified. Also, the spring loaded stops on this one are too stiff and the slide motor won’t move with these. Again, back to the donor mirror.Lastly, these also do not include power folding. Yes, you could use the donor mirrors to make it work and I did, but it is a pain, involved some dremeling and some creative work. Not for the faint of heart.Finally, if you want to reuse your painted or chrome cap on the mirror you can but there is about a 1/16” gap at bottom - again, just slightly different than oem. It fits, but doesn’t quite fully lock. A little super sticky tape worked fine on the back bottom lip.4 stars for price and it looks good. Had I used as is as drop in, wiring issue keeps it from 5 star (id have done 3.5). All else is on me.Tech support gives you a website that doesn’t work and phone number that goes to dead line with apology voicemail.

These things are a joke and misleading. Did they fit? Sure. But what they don’t tell you, aside from not mechanically extending or folding in like the original ones, but the exterior temp gauge is set up in the original ones. So it doesn’t read the outside temperature. Moreover, Ford built this into the AC system on the truck to gauge interior temps. So, mine read -40 degrees outside so my AC compressor on the truck wouldn’t kick on. I thought something was wrong with the ac so I took it in. Nope, it’s these POS foreign made mirrors. Put the originals back on and everything works like it’s supposed to. Now...I’m past my 30 day return policy because it took me a while to get it into the shop. Awesome.

After reading other reviews I expected the mirror operation to be backwards and just switched the wires and everything works perfect. I am very pleased with this product and its price

First off, I like the mirrors and won’t complain much, cause they are cheap compared to the full original XLT mirrors. So I don’t have power out/in or fold back, but that’s ok. On 2011 and newer, the outside temp sensor is located on a cover plate under the passenger mirror. The new mirrors don’t include the sensor, yet the wire harness is there. I simply unplugged mine and even though the harness connector looks different, it will plug in. The new mirror cover plate is sized different, but no worries, just tuck the sensor in there. Only other thing is my new mirrors move the glass in/out backwards, no biggie. New OEM mirrors are like $600 a piece, so I’m not complaining. Great mirror to save hundreds !

But for the price you might've figured that right?I bought these 8/24/2021The lower passenger side mirror fell off 12/26/2023Pros:InexpensiveHas wiring for ambient temp sensorEasy to install.Cons:Lower mirror glass is not replaceable.Mirror adjustments work backwards.Poor quality glass, think fun house mirrors.Glass wobbles and shakes while driving.No temp sensor or connector, you need to use the ones from your original mirror.I'll be replacing them with a set of Trail Ridge mirrors.They're $100.00 more but have a lifetime warranty and a temp sensor

Nice product great price and really good quality