Omnipod 5 Overpatches, Dash – Pack of 25 – Waterproof, Transparent Patches for Tubeless, automated Pump, Sensor is NOT Included

Works perfectly without skin pulling or falling off. Donut shaped with a hole in the middle it effectively makes the sensor adhesive larger and more secure. Used many different sensor covers and this is the only one that does not irritate my skin and stays on for 15 days. Good job!Note: is donut shaped with a hole in the middle. If you want waterproof for swimming- look elsewhere.

These are affordable and perform exactly as I need them to. Sometimes I do not want the sensor itself covered. Just an extension and protection of the adhesive ring that comes out from the base of the sensor. That's when I go to these. Easy one hand application. You won't need help. Keeps the adhesive edge around the sensor from coming up towards the last few days of wear. I have long curly hair that gets washed and conditioned daily, without these or a full cover the emollients in my hair care products weaken the adhesive. With these my sensors always last a full 14 days. Be aware, these are not meant to protect from hard bumps. You need a reusable cover of some sort under this or another cover tape for that kind of protection. These are sheer and light weight. I don't even feel them there once they are on. Very hard to see it so unlike the decorative style tapes they don't draw attention to the sensor. I'm not sensitive about the device being noticed by others but I don't go out of my way to advertise either. The Libre 3 is especially sensitive to moisture and. heat, so these are great to keep the sensor adhered and still allow the sensor to breath since it is not covered over. The waterproof-ness is that it protects the adhesive backing edge from water loosening, NOT that it keeps water out of the sensor all together. Any water that gets in through the hole on top of the sensor will drain and evaporate out through the hole as will sweat just as the sensor is designed. Can't guarentee for others, but I tend to be adhesive reactive and these have been just fine. No redness or blistering, no itching. They stay on and come off without taking skin when I want them to come off. They also do not take the sensor with them. I. recommend pressing downrightly on. the center of. the sensor as you remove this tape if you need to remove it before the sensor ends as it is stuck to the sensor. adhesive backing along the protruding edges. I have not had a problem, but why tempt fate?

These monitor covers work great! They have great adhesion and stay on for two weeks! Very impressed with this product! Thank you! Seller did an awesome job with speedy delivery!

Many of the glucose patch covers on Amazon are designed to cover the entire patch, and this is what I had assumed these were. I spent 30 minutes trying to separate the paper backing from the "patch" before realizing that the "patch" portion is a donut-shaped ring that encloses the outside of the glucose monitor and overlaps with the monitor's built-in patch to provide a seal. The minimal instructions sort-of show this, but it's not super-clear. In any case, once I figured that out, it was easy to apply the patch and after two days it seems to be holding fine.The good part about this design is that it's very light weight and no more noticeable than the monitor itself. The downside (I guess) is that it relies on the overlap with the monitor's seal, so if you didn't do a good job putting the glucose monitor on in the first place, this isn't going to fix it.The other important point is that you need to get the patch that exactly matches the dimensions of your monitor to get the seal correct. I have a Freestyle Libre 3+, and the patch for the Libre 3 fit perfectly.

Perfect for keeping my libre 3 plus sensor secure. The sensor has a very narrow adhesive around it and it is easily knocked off of pulled loose. This adds an extra layer of adhesive. It is a wide border that fits around the sensor. So far I've bumped against door frame and accidentally passed a washcloth over it and it's pretty secure. I haven't had to Remove it yet as ive only worn it for a little over a week,but it shouldn't be difficult maybe a little oil or rubbing alcohol to loosen

Product does not work at all. The ring goes completely around the Libre3. It makes no contact with the device. It literally serves no purpose. It would have worked on the 2. When I connected with the manufacturer, they tried to tell me that the FDA won’t let them cover the device…. Like the FDA regulates bandages???!!!!##

Just finished my 1st pack of 20. Works great. Stays on the full 14 days. I take 2 showers a day and workout, so the patch sees a lot of moisture. Just placed 2nd order. Tad tricky at times to apply, but gets easier over time with practice. I find putting a finger thru the donut, then touching the sensor with that finger helps center the patch.

I have the omnipod 5 and I’ve been having issues with my pods falling off. I bought these because I liked that it said waterproof and it was clear, so it wouldn’t be as obvious that I had anything else on my arm. However, these ended up giving me a rash on my arm, and since they are plastic, it really hurt to pull them off. My pod most certainly stayed on! Which is why I’m not giving it less stars, but if you have sensitive skin, I would stay away from these. I ended up going back to a cloth based patch and they are working much better. In addition, I felt like it was a little difficult to put on, they fit tightly around the pod, so it’s a little hard to do yourself, and the wrapping is a thin paper material, so if youre not careful taking the backing off, it rips. These just didn’t work for me which is disappointing, I used them for 3-4 pods before I developed a rash so now I have them sitting around and idk what to do with them.